This guide explains what a split unit is, what a proper installation involves, how to plan the placement, what happens on the day, and how to prepare so the job goes smoothly. It is written for homeowners who want to understand the process, not just pay for it. For a tailored quote on your own home, request a free one.

What is a split unit aircon?

A split system splits the air conditioner into two parts: an indoor unit, mounted high on a wall (or recessed into a ceiling, for a cassette), and an outdoor unit, or condenser, that sits outside the home. The two are connected by refrigerant piping, electrical cabling and a condensate drain, all usually concealed in the wall or run in trunking.

The indoor unit contains the evaporator coil and the fan that blows air across it into the room. The outdoor unit contains the compressor, the condenser coil and another fan that rejects heat to the outside air. The refrigerant circulates between them, absorbing heat from the indoor air and releasing it outside. In an inverter unit, the compressor varies its speed to match the cooling demand; in a non-inverter unit, it runs at full speed or not at all.

This split design is what makes the system quiet indoors — the noisy compressor is outside, in the outdoor unit, while the indoor unit has only a fan and a coil. It is also efficient, because the refrigerant loop is sealed and short. For most South African homes, a wall-mounted split is the default and the right choice. See best aircon for a house in South Africa for how it compares to other types.

What a proper installation involves

A proper split unit installation is more than bolting two boxes to a wall. It is a sequence of steps, each of which has to be done correctly for the system to cool well, run efficiently, and last. Understanding the steps helps you tell a thorough installer from a rushed one.

  • Site assessment — choosing where the indoor and outdoor units go, how the piping runs, and what electrical work is needed.
  • Mounting the indoor unit — fixing the mounting plate to the wall, level and secure, then hanging the unit.
  • Drilling the wall penetration — a hole through the wall for the piping, cabling and drain, angled so condensate flows out.
  • Running the refrigerant piping, electrical cable and drain — connecting indoor to outdoor, usually concealed in the wall or trunking.
  • Mounting the outdoor unit — on a wall bracket, a stand or a slab, level and with good airflow around it.
  • Connecting and flaring the refrigerant lines — joining the copper pipes to the units with flared fittings, leak-free.
  • Vacuuming the refrigerant lines — removing air and moisture from the pipework before releasing refrigerant, essential for efficiency and compressor life.
  • Electrical connection — wiring to an isolator and circuit protection, sized to the unit’s load.
  • Testing and commissioning — running the unit, checking pressures and temperatures, confirming cooling and drainage, and explaining operation to you.

Skipping or rushing any of these steps compromises the result. A poorly vacuumed line leaves moisture in the system, which corrodes internals and reduces efficiency. A drain that is not angled correctly leaks water down the wall. An undersized electrical connection is unsafe and can void the warranty. A thorough installer does every step properly, and a transparent quote reflects the time that takes.

Planning the indoor unit placement

Where the indoor unit goes affects comfort, efficiency and the look of the room. A few principles guide good placement.

  • Height — mount high on the wall, so cool air falls and circulates evenly through the room.
  • Airflow — position the unit so the airflow reaches across the room without obstruction, and so it does not blow directly onto a bed, sofa or desk.
  • Clearance — leave space around the unit for airflow and for service access; do not tuck it into a corner or behind a curtain.
  • Piping run — place the indoor unit as close as practical to the outdoor unit to minimise the piping run, which reduces cost and improves efficiency.
  • Drainage — the condensate drain has to run downhill to a suitable discharge point; placement has to allow for that.
  • Aesthetics — consider where the unit and any visible piping will sit in the room; concealed piping looks neater and is usually worth the small extra effort.

In a bedroom, avoid pointing the airflow directly at the bed — a unit that blows cold air onto a sleeping person is uncomfortable and unhealthy. In a lounge, aim the airflow across the room rather than at a seating area. In a kitchen or open-plan space, position the unit to reach the whole area, or consider a second unit or a cassette for large spaces.

Planning the outdoor unit placement

The outdoor unit is the part people forget to plan, and it causes the most neighbour disputes and service problems. Good placement matters.

  • Airflow — the unit needs clear airflow around it to reject heat; do not box it in or push it against a wall.
  • Access — leave room for a technician to service it; a unit jammed in a corner is hard and costly to maintain.
  • Noise — position it away from bedroom windows (yours and your neighbour’s); outdoor unit noise carries.
  • Sun — where possible, shade the unit from direct sun, which improves efficiency; avoid enclosing it so tightly that air cannot circulate.
  • Mounting — on a wall bracket, a stand or a slab, level and secure, with vibration isolation to prevent rattling.
  • Drainage — the outdoor unit also produces condensate in some modes; route it to a suitable discharge point.

In townhouse complexes, body-corporate rules often dictate where the outdoor unit may go and how it must be mounted. Mention your complex when you request a quote so the placement can be planned within the rules. In freestanding homes there is usually more flexibility, but the principles of airflow, access, noise and sun still apply.

The piping and electrical connection

The connection between indoor and outdoor units is the hidden heart of the installation, and it is where quality shows. The refrigerant piping is copper, insulated to prevent condensation and energy loss, and joined to the units with flared fittings that have to be leak-free. The electrical cable carries power and control signals. The condensate drain carries water away from the indoor unit.

A proper installation conceals these in the wall where possible, with only a short exposed run where the lines enter the outdoor unit. The wall penetration is sealed to prevent draughts, water ingress and pests. The piping run is kept as short and direct as practical — every metre of piping adds cost and slightly reduces efficiency, and every bend adds resistance.

The electrical side is just as important. The unit needs an isolator within reach for safe servicing, and circuit protection sized to its load. For larger units, or where several units share a board, a dedicated circuit may be required. Older homes may need a board upgrade to support a modern unit safely. This work has to be done to standard — not just for safety, but because many manufacturers require proof of compliant electrical installation to honour a warranty claim.

Vacuuming and commissioning: the steps that get skipped

Two steps separate a proper installation from a rushed one: vacuuming the refrigerant lines and commissioning the system. They are invisible to the homeowner, which is exactly why cut-price installers skip them.

Vacuuming uses a vacuum pump to remove air and moisture from the refrigerant lines before the refrigerant is released into the system. Air in the lines reduces cooling efficiency; moisture reacts with the refrigerant to form acids that corrode the compressor and shorten its life. A unit installed without proper vacuuming may cool adequately at first but fail early and run inefficiently — and the cause is invisible until the compressor dies.

Commissioning is the final test: the installer runs the unit, checks the operating pressures and temperatures, confirms that it cools to specification, verifies that the condensate drains properly, and walks you through the operation and basic maintenance. A thorough installer does this and documents it; a rushed one plugs it in and leaves. Ask whether your installer vacuums the lines and commissions the system — the answer tells you a lot about the quality you are paying for.

How long does a split unit installation take?

A straightforward single split installation — indoor unit on an external wall, outdoor unit nearby, short piping run, existing suitable power point — is typically completed in a few hours. More complex jobs take longer: long piping runs, work at height, piping through a tiled roof, a dedicated circuit, or multiple units in one visit all add time.

The full breakdown of what affects installation time is in how long does aircon installation take? — but the short version is that a clean, simple installation is a half-day job, and a complex one can run to a full day or more. A good installer gives you a realistic time estimate as part of the quote.

How to prepare for installation day

A little preparation makes installation day smoother and protects your home.

  • Clear the area around where the indoor unit will go — move furniture, pictures and curtains away from the wall.
  • Clear access to the outdoor unit location — inside and outside, so the installer can reach both with tools and a ladder.
  • Make sure the electrical board is accessible — the installer may need to work at the board for the electrical connection.
  • Protect floors and surfaces near the work area — drilling and running piping creates dust; a drop sheet helps.
  • Confirm access for the installer — parking, gate codes, estate clearance if you live in a complex.
  • Be available, or have someone available, to approve the placement and receive the handover at the end.

A clear site lets the installer work efficiently and safely, and a quick handover at the end ensures you know how to operate and maintain the unit. A thorough installer will show you the remote, explain the modes, point out the filter access for cleaning, and confirm the drainage is working before they leave.

After installation: first run and maintenance

Once the unit is commissioned, the first run confirms it cools properly and drains correctly. Watch for a few things in the first days: steady cooling to setpoint, no water dripping down the indoor wall (a sign the drain is blocked or poorly angled), and no unusual noises from either unit. A small “new unit” smell for the first hour is normal as dust burns off the elements; persistent smells or noises are not.

Ongoing maintenance is simple but important. Clean or replace the indoor filters regularly — a clogged filter reduces airflow, efficiency and cooling, and is the most common cause of “my aircon is not cooling” calls. Keep the outdoor unit clear of leaves and debris so it can reject heat. Have the unit serviced professionally at the recommended interval to check refrigerant levels, clean the coils, and catch small issues before they become failures. See our care plans for routine maintenance options.

A well-installed, well-maintained split unit cools quietly and efficiently for many years. The installation quality is the foundation — get it right once, and the unit rewards you with comfort and low running cost for its whole life.

Common installation problems and how to avoid them

A few problems show up repeatedly in poorly installed split units, and most are avoidable. Knowing them helps you spot a rushed job and ask the right questions.

Water dripping down the indoor wall is the most visible symptom, and it almost always means the condensate drain is blocked or poorly angled. The drain has to run downhill from the indoor unit to its discharge point; if it sags, kinks, or is routed uphill, water backs up and overflows. A proper installation tests the drain during commissioning — the installer pours water into the tray and confirms it runs out freely — so this is caught before the installer leaves.

Poor cooling despite a new unit usually points to one of three causes: an undersized unit, a refrigerant line that was not vacuumed (leaving air and moisture that reduce efficiency), or a low refrigerant charge from a leaky flare fitting. The first is a sizing mistake caught at the quote stage; the second and third are installation-quality issues that proper vacuuming and careful flaring prevent. This is why those invisible steps matter so much.

A noisy outdoor unit is often a mounting issue — a bracket that is not level, a unit that is not isolated from the wall, or a location that reflects sound toward a window. Good mounting with vibration isolation and thoughtful placement prevents most outdoor noise complaints, which is especially important in close-spaced suburbs and complexes.

Finally, a unit that trips the breaker repeatedly usually means the electrical protection is undersized or the wiring is faulty. This is a safety issue, not a nuisance, and it points to electrical work that was not done to standard. A thorough installer sizes the circuit protection to the unit’s load and tests it before handover, so the breaker does its job only when there is a genuine fault.

The bottom line

A split unit aircon is the right choice for most South African homes, but a good result depends on a proper installation: careful placement of both units, a short and well-sealed piping run, compliant electrical work, vacuuming of the refrigerant lines, and thorough commissioning. The steps that get skipped — vacuuming and commissioning — are the ones that determine whether the unit lasts for years or fails early.

Choose an installer who does every step properly, prepare the site, and maintain the unit after installation. And remember our price promise: bring us any comparable written quote from another aircon company in Gauteng and we will do our best to beat it.

Ready to install a split unit? Request a free quote — tell us the room, the wall and how you use the space, and we will plan the placement and give you a tailored price.